P2282 Air Leak Between Throttle Body and Intake Valves
OBD-II Trouble Code Technical Description
Air Leak Between Throttle Body and Intake Valves
What does that mean?
This diagnostic trouble code (DTC) is a generic powertrain code and applies to many OBD-II vehicles (1996-newer). Although generic, the specific repair steps may vary depending on make/model. That may include but is not limited to vehicles from Vauxhall, Chevrolet, Suzuki, Saturn, Chevy, Corsa, Ford, etc. Although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration.
If your vehicle has stored a code P2282, it means that the powertrain control module (PCM) has detected a degree of airflow at the throttle body which does not exist in the combustion chamber.
In order for today���s engines to perform at peak efficiency, air and fuel must be regulated precisely. The fuel pump and fuel injectors provide fuel in adequate supply and the throttle body (or throttle bodies) allows metered air to enter the intake. The delicate air/fuel ratio must be carefully monitored and adjusted; constantly. This is accomplished using the PCM with inputs from engine sensors such as the MAF, the manifold air pressure (MAP) sensor, and the heated oxygen sensors (HO2S).
After comparing the amount of ambient air being drawn into the MAF sensor and the air being drawn into the engine intake manifold, if the PCM detects that the two exceed the maximum allowable threshold for variation, a code P2282 may be stored and a malfunction indicator lamp (MIL) illuminated. Multiple drive cycles with a failure may be required for MIL illumination.
A typical MAF sensor:
What is the severity of this DTC?
A stored code P2282 will likely be accompanied by severe drivability symptoms. The conditions which contributed to code storage should be rectified as quickly as possible.
What are some of the symptoms of the code?
Symptoms of a P2282 trouble code may include:
What are some of the common causes of the code?
Causes for this code may include:
What are some P2282 troubleshooting steps?
In order to diagnose a code P2282, a diagnostic scanner, a digital volt/ohmmeter (DVOM), and a source of vehicle specific diagnostic information will be required.
If you can use your source of vehicle information to locate a technical service bulletin (TSB) that matches the vehicle year, make, and model; as well as the engine size, code/s stored, and symptoms exhibited, it could yield helpful diagnostic information.
The engine should be in good working order and capable of producing sufficient vacuum.
Start by carefully checking the intake manifold area for signs of a vacuum leak (with the engine running). Any vacuum leak that is large enough to cause a code P2282 to be stored will likely be very evident with the engine running (don���t forget the EGR valve and the PCV valve).
If MAF codes accompany the P2282, carefully inspect the MAF Sensor hot wire for unwanted debris. If debris is present on the hot wire, follow manufacturer���s recommendations for cleaning the MAF sensor. Never use chemicals or cleaning methods which are not specifically recommended by the automaker.
Use the scanner (connected to the vehicle diagnostic connector) to retrieve all stored codes and pertinent freeze frame data. It is a good idea to write this information down before clearing the codes then test-drive the vehicle until the PCM either enters readiness mode or the code is reset.
If the PCM enters readiness mode at this time, the code is intermittent and may be much more difficult to diagnose. If this is the case, the conditions which contributed to the code being stored may need to worsen before an accurate diagnosis can be made.
However, if the code is immediately reset, completing the next step of your diagnosis will require that you search your vehicle information source for diagnostic flow-charts, connector pin-out charts, connector face views, and component testing procedures/specifications.
With the air inlet pipe intact and the engine in good working order, follow manufacturer���s specifications to test the MAF and MAP sensors using the DVOM. If both these sensors are functional, use the voltage drop method to test system circuit.
Need help?
Let us fix your problem. You are most welcome our diagnosis experts have in most cases the knowledge and skills to find the cause of the error code p2282 and to solve the problems.
Make an appointment for diagnosis
"Delete Error Code Permanently, Disable DTC Error Code Function for p2282 in the ECU"
In extreme cases, we even have the option to permanently remove the specific DTC p2282 and disable the function of the specific error code in the ECU. All other fault code functions will then continue to work to protect the engine. This is different from clearing an error code with a diagnostic device. We have the option to permanently remove the function of the specific error code, so that it never comes back. Also emergency running that occurs on the specific error code can be solved in most cases.
Of course we prefer to first try to solve the cause of the error code, but sometimes the only solution is to permanently disable the DTC function of p2282.
