P0162 02 Sensor Circuit Malfunction (Bank 2 Sensor 3)
OBD-II Trouble Code Technical Description
O2 Sensor Circuit Malfunction (Bank 2 Sensor 3)
What does that mean?
This diagnostic trouble code (DTC) is a generic powertrain code, which means that it applies to OBD-II equipped vehicles. Although generic, the specific repair steps may vary depending on make/model.
The O2 (oxygen) sensors measure oxygen content in the exhaust, whether rich or lean. The PCM (powertrain control module) then uses this information to regulate fuel injector pulse in order to keep the proper air:fuel ratio. The O2 sensors are very important for the proper operation of the engine.
Fouled or faulty O2 sensors can cause the PCM to add or take away fuel based on the faulty O2 sensor data which can cause a false lean or rich condition. A P0162 code refers to the Bank 2,3 O2 sensor, or the third sensor downstream (post-cat) on Bank 2. It is a four wire sensor. The PCM supplies a ground circuit and a reference voltage circuit of about 0.5 volts or half a volt. Also for the O2 sensor heater element there is a battery voltage supply wire (usually from the power distribution center) and another ground circuit for that. The O2 sensor heater allows the O2 sensor to warm up faster, thus achieving closed loop in less time than it would normally take for the exhaust to warm the sensor up to operating temperature. This creates less exhaust emissions at cold startup. The O2 sensor varies the supplied reference voltage based on oxygen content in the exhaust. It is capable of varying from about 0.1 to 0.9 volts, 0.1 V indicating lean exhaust and 0.9 V indicating rich exhaust. This P0162 code indicates that the Bank 2, 3 O2 sensor is stuck low for too long or is inactive.
Symptoms
Often post-cat O2 sensor problems present few drivability issues since they are inputs to the PCM to monitor catalytic converter quality and don’t directly control fuel. Sometimes no symptoms are noticeable. However the following may be possible on some vehicles:
Causes
Potential causes of a P0162 code include:
Possible Solutions
Warm the engine up to normal operating temperature. Using your scan tool’s live datastream, check the signal voltage for the Bank 2,3 O2 sensor at idle. Is it stuck low and not switching? If so, increase engine RPMs for a minute or so and observe if the sensor begins switching or changing voltage. If it does after a period of elevated idle, check under the vehicle for rusty exhaust components or holes in the exhaust near the O2 sensor(s). Repair as necessary. If the exhaust is intact, then suspect a sluggish Bank 2,3 O2 sensor and replace it. If you observe that the O2 sensor remains low on the datastream, then unplug it and observe the reading. It should now be showing reference voltage, or half a volt (0.5 v). If it does, check for connector problems, water intrusion, damage to the sensor, etc. If all is okay, replace the faulty Bank 2,3 O2 sensor.
If the voltage reading is still low after unplugging the O2 sensor, then suspect a problem with the wiring. Visually inspect the wiring harness making sure that there is no contact with hot exhaust components and that all the harness retainers are in place. Repair as necessary If no wiring harness issues exist, use a voltmeter to check for reference voltage from the PCM at the unplugged connector. It should be reading reference voltage, or about half a volt (0.5v). If voltage reading is too high, repair the short to voltage on the signal circuit.
Related DTC Discussions
Register now to ask a question (free)
Need more help with a p0162 code?
If you still need help regarding the P0162 trouble code, please post your question in our FREE car repair forums.
NOTE: This information is presented for information purposes only. It is not intended as repair advice and we are not responsible for any actions you take on any vehicle. All information on this site is copyright protected.
Need help?
Let us fix your problem. You are most welcome our diagnosis experts have in most cases the knowledge and skills to find the cause of the error code p0162 and to solve the problems.
Make an appointment for diagnosis
"Delete Error Code Permanently, Disable DTC Error Code Function for p0162 in the ECU"
In extreme cases, we even have the option to permanently remove the specific DTC p0162 and disable the function of the specific error code in the ECU. All other fault code functions will then continue to work to protect the engine. This is different from clearing an error code with a diagnostic device. We have the option to permanently remove the function of the specific error code, so that it never comes back. Also emergency running that occurs on the specific error code can be solved in most cases.
Of course we prefer to first try to solve the cause of the error code, but sometimes the only solution is to permanently disable the DTC function of p0162.
