P2461 Diesel Particulate Filter Pressure Sensor “B” Circuit High

Home » OBD Codes » P2400-P2499 » P2461 Diesel Particulate Filter Pressure Sensor “B” Circuit High

P2461 Diesel Particulate Filter Pressure Sensor “B” Circuit High

OBD-II Trouble Code Technical Description

Diesel Particulate Filter Pressure Sensor B Circuit High

What does that mean?

This diagnostic trouble code (DTC) is a generic powertrain code, which means that it applies to all 1996-newer vehicles (Ford, Dodge, GMC, Chevrolet, Mercedes, VW, etc.). Although generic, the specific repair steps may vary depending on make/model.

When a code P2461 is stored, the powertrain control module (PCM) has detected a high voltage input signal from the circuit of the diesel particulate filter (DPF) pressure sensor that has been given the designation B. This code is used only in vehicles equipped with diesel engines.

DPF systems are quickly becoming the norm in diesel powered vehicles. They are designed to remove ninety-percent of carbon particles (soot) from diesel engine exhaust. Diesel engines are known for the black smoke that billows from the exhaust (especially under heavy acceleration). Soot is the main component of this smoke. The DPF is contained in a steel housing and normally resembles a muffler or catalytic converter. It is positioned before the catalytic converter (and/or the NOx trap). In theory, large soot particles are trapped in the DPF element while smaller particles and other (exhaust gas) compounds are allowed to flow through. Paper fibers, metal fibers, ceramic fibers, silicone wall fibers, and cordierite wall fibers are some elemental compounds that are currently being used to trap large soot particles. The most common type of fiber used in DPF applications is ceramic based cordierite because of its excellent filtration characteristics. Cordierite is known for having problems with overheating at higher temperatures, making it susceptible to malfunctions in vehicles equipped with passive DPF systems.

Of course, the filtration element is the heart of the DPF. Large particles of soot should be trapped between the fibers and engine exhaust is allowed to flow through. When there is a large accumulation of soot particles accumulated by the DPF, exhaust pressure increases. After exhaust pressure has reached a predetermined level, the filtration element must be regenerated. Regeneration of the DPF permits exhaust gases to continue flowing through the DPF and helps to maintain the correct level of exhaust pressure.

Systems that are automatically regenerated are known as active DPF systems. The PCM is programmed to inject chemicals (including but not limited to diesel fuel and diesel exhaust fluid) into the exhaust at programmed intervals in this type of system. An electronically controlled injection causes exhaust temperature to increase, allowing trapped soot particles to burn and be released as ions of nitrogen and oxygen. Similar in theory are passive DPF systems. They require some type of input from the operator. Some models require a qualified repair facility for the regeneration process. The DPF regeneration could take several hours to accomplish once it is begun.

After the filtration element is effectively regenerated, exhaust pressure should decrease to an acceptable level. The DPF pressure sensor is typically mounted remotely and away from the DPF. Exhaust back pressure is monitored (as it enters the DPF) using silicon hoses (connected to the DPF and the DPF pressure sensor).

A code P2461 will be stored if the PCM detects an exhaust pressure condition that is higher than manufacturer’s specifications or an electrical input signal from DPF pressure sensor A which is higher than programmed limitations.

Symptoms & Severity

Conditions that could lead to this code may also lead to internal engine or fuel system damage and should be considered urgent. Symptoms of a P2461 code may include:

  • Excessive black smoke from the exhaust
  • Increased engine temperatures
  • Higher than normal transmission temperatures
  • Diminished engine performance
  • Causes

    Potential causes for this code to set are:

  • Exhaust leaks
  • Clogged DPF pressure sensor tubes/hoses
  • Open or shorted circuit/s in the DPF pressure sensor B circuit
  • Faulty DPF pressure sensor
  • The diesel exhaust fluid reservoir may be empty
  • Improper diesel exhaust fluid
  • Inept DPF regeneration
  • The active DPF regeneration system is inoperative
  • Diagnostic and Repair Procedures

    A good starting point is always to check for technical service bulletins (TSB) for your particular vehicle. Your issue may be a known issue with a known fix put out by the manufacturer and can save you time and money during diagnosis.

    In order to diagnose a code P2461, a digital volt/ohmmeter, a manufacturer’s service manual, and a diagnostic scanner will be needed.

    I recommend that you start your diagnosis with a visual inspection of related harnesses and connectors. Inspect wiring that is routed near hot exhaust components and/or jagged edges. Be certain that you check alternator output, battery voltage, and battery terminal ends at this time.

    Proceed by connecting the scanner and retrieving all stored codes and freeze frame data. Don’t forget to write this information down for future reference, and then clear all stored codes.

    Use the DVOM and follow manufacturer’s recommendations for testing the DPF pressure sensor. Consult the service manual for specific instructions. Any sensor that fails to comply with manufacturer’s resistance specifications must be replaced.

    The DPF pressure sensor supply hoses should be checked for clogs and/or breakage if the sensor checks out. Replace hoses that are burnt, cracked, or collapsed (high temp silicon hoses are recommended).

    If sensor supply lines are intact, and the sensor is operational, you may begin testing system circuits. To prevent PCM damage, disconnect all related controllers prior to testing resistance and/or continuity with the DVOM.

    Additional diagnostic notes:

  • Check DPF regeneration fluid before attempting to diagnose this code
  • Clogged sensor ports and clogged sensor tubes are common when this code is stored
  • DPF pressure sensor hoses that are melted or cut, may need to be rerouted after replacement
  • Need help?

    Let us fix your problem. You are most welcome our diagnosis experts have in most cases the knowledge and skills to find the cause of the error code p2461 and to solve the problems.

    Make an appointment for diagnosis

    "Delete Error Code Permanently, Disable DTC Error Code Function for p2461 in the ECU"

    In extreme cases, we even have the option to permanently remove the specific DTC p2461 and disable the function of the specific error code in the ECU. All other fault code functions will then continue to work to protect the engine. This is different from clearing an error code with a diagnostic device. We have the option to permanently remove the function of the specific error code, so that it never comes back. Also emergency running that occurs on the specific error code can be solved in most cases.

    Of course we prefer to first try to solve the cause of the error code, but sometimes the only solution is to permanently disable the DTC function of p2461.

    Make an appointment for permanent removal of p2461