P2277 O2 Sensor Signal Biased/Stuck Rich Bank 2 Sensor 3

Home » OBD Codes » P2200-P2299 » P2277 O2 Sensor Signal Biased/Stuck Rich Bank 2 Sensor 3

P2277 O2 Sensor Signal Biased/Stuck Rich Bank 2 Sensor 3

OBD-II Trouble Code Technical Description

O2 Sensor Signal Biased/Stuck Rich Bank 2 Sensor 3

What does that mean?

This is a generic powertrain code, which means it covers all OBD-II equipped vehicles, 1996-newer. Auto brands may include but are not limited to Hyundai, Ford, Jeep, Chevy, BMW, Kia, Holden, Dodge, etc. However, specific troubleshooting steps will vary depending on the vehicle.

This P2277 diagnostic trouble code (DTC) refers to the postalytic converter O2 (oxygen) sensor on bank #2, sensor #3. This post sensor is used for monitoring the efficiency of the catalytic converter. The converter’s job is to reduce emissions out the tailpipe. When the signal from the O2 sensor is detected by the PCM as being stuck rich or biased rich, this DTC is set.

The P2277 DTC refers to the second downstream sensor (after the second catalytic converter), sensor #3 on bank #2. Bank #2 is the side of the engine that does not contain the #1 cylinder.

This code is basically telling you that the signal put out by the particular oyxgen sensor is stuck rich (meaning too little air in the exhaust).

A typical oxygen O2 sensor:

Symptoms

Most likely you will not notice any drivability issues since this is not sensor #1. You will notice Malfunction Indicator Lamp (MIL) illumination. In some cases however, the engine may run rough.

Potential Causes

The causes for this DTC may include:

  • Contaminated or failed HO2S2 (Sensor 3)
  • HO2S2 wiring/circuit problem
  • Fuel pressure incorrect
  • Faulty fuel injector
  • Engine coolant leak
  • Faulty purge solenoid valve
  • PCM has failed
  • Diagnostic and Repair Procedures

    Visually inspect the wiring and connectors for corrosion, rubbed / chafed / bent wires, wiring pins bent/loose, burnt appearance, and/or crossed wires. Repair or replace as required.

    Check for exhaust leaks or other problems, repair as necessary.

    Using a digital volt ohm meter (DVOM) set to ohms, check harness connectors for resistance. Compare to manufacturer specifications. Replace or repair as required.

    If you have access to an advanced scan tool, use it to monitor the sensor readings as viewed by the PCM (engine running, at normal operating temperature in closed loop mode). The rear heated oxygen sensor (HO2S) normally sees a fluctuating voltage between 0 & 1 volt, for this DTC you’ll likely see the voltage "stuck" at 1V. Revving the engine should cause the sensor’s voltage to change (react).

    The most common fixes for this DTC seem to be either an exhaust air leak, a wiring problem with the sensor/wiring, or the sensor itself. If you replace the O2 sensor, buy an OEM one (manufacturer brand) for best results.

    If you remove the HO2S oxygen sensor, inspect it for contamination from fuel, engine oil, and coolant.

    Other troubleshooting ideas: Use a fuel pressure tester, check the fuel pressure at the Schrader valve on the fuel rail. Compare to manufacturers specification. Inspect the purge solenoid valve. Inspect fuel injectors. Inspect coolant passages for leaks.

    Need help?

    Let us fix your problem. You are most welcome our diagnosis experts have in most cases the knowledge and skills to find the cause of the error code p2277 and to solve the problems.

    Make an appointment for diagnosis

    "Delete Error Code Permanently, Disable DTC Error Code Function for p2277 in the ECU"

    In extreme cases, we even have the option to permanently remove the specific DTC p2277 and disable the function of the specific error code in the ECU. All other fault code functions will then continue to work to protect the engine. This is different from clearing an error code with a diagnostic device. We have the option to permanently remove the function of the specific error code, so that it never comes back. Also emergency running that occurs on the specific error code can be solved in most cases.

    Of course we prefer to first try to solve the cause of the error code, but sometimes the only solution is to permanently disable the DTC function of p2277.

    Make an appointment for permanent removal of p2277