P219B Bank 2 Air/Fuel Ratio Imbalance

Home » OBD Codes » P2100-P2199 » P219B Bank 2 Air/Fuel Ratio Imbalance

P219B Bank 2 Air/Fuel Ratio Imbalance

OBD-II Trouble Code Technical Description

Bank 2 Air/Fuel Ratio Imbalance

What does that mean?

This is a generic diagnostic trouble code (DTC) and applies to many OBD-II vehicles (1996-newer). That may include but is not limited to vehicles from Toyota, Dodge, Ford, Honda, Jeep, Chevy / Chevrolet, GMC, Ram, etc. Although generic, the exact repair steps may vary depending on year, make, model and powertrain.

When a code P219B is stored, it means that the powertrain control module (PCM) has detected an air to fuel ratio imbalance for the bank of the engine which does not contain the number one cylinder.

In order to monitor the air to fuel ratio for each engine bank, the PCM uses data input from heated exhaust oxygen sensors (sometimes called air fuel sensors).

Each oxygen sensor is constructed using a zirconium dioxide sensing element situated in the center of a vented steel housing. Tiny electrodes (usually of platinum) attach the sensing element to wire leads in the oxygen sensor harness connector and the connector plugs into the controller area network (CAN) which connects the oxygen sensor wiring harness to the PCM connector.

Each oxygen sensor is threaded (or studded) into an exhaust pipe. It is situated so the the sensing element is near the center of the pipe. As spent exhaust gases exit the combustion chamber (via the exhaust manifold) and continue through the exhaust system (including catalytic converters), they flow over the oxygen sensors. Exhaust gases enter the oxygen sensor through specially designed vent holes in the steel housing and swirl around the sensing element. Swirling ambient air is drawn through wire lead cavities in the sensor housing in order to fill a tiny chamber in the middle of the sensor. The air (in the tiny chamber) is then heated. This forces the oxygen ions to produce energy that is recognized by the PCM as voltage.

Variations between the number of oxygen ions in ambient air (drawn into the O2 sensor), and the number of oxygen molecules in the exhaust, cause the oxygen ions inside the O2 sensor to bounce from one platinum layer to the other, very swiftly and repetitively. As the surging oxygen ions shift between platinum layers, variations in oxygen sensor output voltage occur. The PCM sees these variations in oxygen sensor output voltage as changes in exhaust oxygen concentration. Voltage signal outputs from the oxygen sensors are lower when more oxygen is present in the exhaust (lean condition) and higher when less oxygen is present in the exhaust (rich condition).

If the PCM detects an imbalance in the air to fuel ratio for a particular bank of the engine, a code P219B will be stored and a malfunction indicator lamp (MIL) may be illuminated. Most vehicles will require multiple ignition cycles (with a failure) for MIL illumination.

A typical oxygen sensor:

What is the severity of this DTC?

An incorrect air to fuel ratio may be the result of insufficient fuel or excessive air (vacuum). A code P219B should be categorized as severe and rectified as quickly as possible.

What are some of the symptoms of the code?

Symptoms of a P219B trouble code may include:

  • Diminished fuel efficiency
  • A lack of general engine performance
  • Stored misfire codes or lean/rich exhaust codes
  • Service engine soon lamp illumination
  • What are some of the common causes of the code?

    Causes for this code may include:

  • Engine vacuum leak (large)
  • Defective oxygen sensor/s
  • Burnt, chafed, broken, or disconnected wiring and/or connectors
  • Engine exhaust leaks
  • A faulty mass air flow or manifold air pressure sensor
  • Bad fuel pump or clogged fuel filter
  • What are some P219B troubleshooting steps?

    All misfire codes, throttle position sensor codes, manifold air pressure codes, and mass air flow sensor codes should be addressed before attempting to diagnose a code P219B. The engine should also be running smoothly and efficiently. If it is determined that either a rich or lean condition exists (with the engine), this must be repaired as it may be the cause of the P219B being stored.

    You will need a diagnostic scanner, a digital volt/ohmmeter (DVOM), and a source of reliable vehicle information in order to accurately diagnose a code P219B.

    You may save yourself time by searching for technical service bulletins (TSB) that replicate the code stored, vehicle (year, make, model, and engine), and symptoms exhibited. This information may be found in your vehicle information source. If you find the right TSB, it could yield a speedy solution to your diagnosis.

    After you connect the scanner to the vehicle diagnostic port and retrieve all stored codes and pertinent freeze frame data, write the information down (in case the code proves to be an intermittent one). After that, clear the codes and test drive the vehicle until one of two things happens; the code is restored or the PCM enters readiness mode.

    The code may actually be more difficult to diagnose if the PCM enters readiness mode at this point, because the code is intermittent. The condition which caused the P219B to be stored may need to worsen before an accurate diagnosis can be made. If the code is restored, continue with the diagnosis.

    You may obtain connector face views, connector pinout charts, component locator charts, wiring diagrams, and diagnostic flow charts (pertaining to the code and vehicle in question) using your source of vehicle information.

    Perform a visual inspection of related wiring and connectors. Repair or replace wiring that has been cut, burned, or damaged.

    If the engine is running smoothly and the code P219B continues to be reset, start the engine and allow it to reach normal operating temperature. Allow the engine to idle (with the transmission in neutral or park). With the scanner connected to the vehicle diagnostic port, observe oxygen sensor input data on the data stream. Narrow the scope of the data stream to include only pertinent data and you will get a faster response.

    If the oxygen sensors are functioning normally, voltage on pre oxygen sensors will cycle continuously between 1 and 900-millivolts once the PCM enters closed loop operation. Post sensors will cycle between 1 and 900-millivolts as well but they will settle at a certain point and remain relatively stable) compared to the pre sensors). Oxygen sensors which fail to cycle adequately should be considered defective if the engine is in good working order.

  • In most cases, you will rectify this code by correcting a rich or lean running engine
  • Need help?

    Let us fix your problem. You are most welcome our diagnosis experts have in most cases the knowledge and skills to find the cause of the error code p219b and to solve the problems.

    Make an appointment for diagnosis

    "Delete Error Code Permanently, Disable DTC Error Code Function for p219b in the ECU"

    In extreme cases, we even have the option to permanently remove the specific DTC p219b and disable the function of the specific error code in the ECU. All other fault code functions will then continue to work to protect the engine. This is different from clearing an error code with a diagnostic device. We have the option to permanently remove the function of the specific error code, so that it never comes back. Also emergency running that occurs on the specific error code can be solved in most cases.

    Of course we prefer to first try to solve the cause of the error code, but sometimes the only solution is to permanently disable the DTC function of p219b.

    Make an appointment for permanent removal of p219b