P2107 Throttle Actuator Control Module Processor

Home » OBD Codes » P2100-P2199 » P2107 Throttle Actuator Control Module Processor

P2107 Throttle Actuator Control Module Processor

OBD-II Trouble Code Technical Description

Throttle Actuator Control Module Processor

What does that mean?

This generic powertrain diagnostic trouble code (DTC) typically applies to all OBD-II equipped vehicles that use a drive-by-wire throttle control system including but not limited to vehicles from Ford, Mazda, Lincoln, Dodge, Mercedes-Benz, Cadillac, Jeep, etc. Anecdotally this code seems to be most common on Ford models with a close second to Lincoln and Mazda.

The P2107 OBD-II trouble code is one of number of possible codes that indicates that the Powertrain Control Module (PCM) has detected a malfunction with the operation of the Throttle Actuator Control System.

There are six codes that are associated with Throttle Actuator Control System malfunctions and they are P2107, P2108, P2111, P2112, P2118 and P2119. Code P2107 is set by the PCM when the Throttle Actuator Control System Module Processor has a generic malfunction.

The PCM controls the Throttle Actuator Control System by monitoring one or more throttle position sensors. The operation of the throttle body is determined by the position of the throttle plate that is controlled by one or more Throttle Actuator Control Motors. The PCM also monitors the accelerator pedal position sensor to determine how fast the driver wants to go and then determines the appropriate throttle response. The PCM accomplishes this by a changing current flow to the Throttle Actuator Control Motor that moves the throttle plate to the desired position. Some malfunctions will cause the PCM to restrict the operation of the Throttle Actuator Control System. This is known as fail-safe or limp mode where the engine is held at idle or may not start at all.

Code Severity & Symptoms

The severity of this code can be moderate to severe based on the specific malfunction. Symptoms of a P2107 trouble code may include:

  • Engine will not start
  • Poor performance that progresses
  • Little, or no throttle response
  • Check Engine Light illuminated
  • Smoke from tailpipe
  • Increased fuel consumption
  • Common Causes Of A P2107 Code

    Possible causes of this code may include:

  • Faulty throttle body
  • Dirty throttle plate or linkage
  • Faulty throttle position sensor
  • Defective accelerator pedal position sensor
  • Throttle actuator control motor is defective
  • Corroded or damaged connector
  • Faulty or damaged wiring
  • Faulty PCM
  • Common Repairs

  • Replacing throttle body
  • Cleaning throttle plate and linkage
  • Replacing throttle position sensor
  • Replacing throttle actuator control motor
  • Replacing accelerator pedal position sensor
  • Cleaning corrosion from connectors
  • Repairing or replacing wiring
  • Flashing or replacing PCM
  • Diagnostic and Repair Procedures

    Check for TSBs

    The first step in the troubleshooting process for any malfunction is to research the Technical Service Bulletins (TSB’s) for the specific vehicle by year, model and power plant. In some circumstances this can save a lot of time in the long run by pointing you in the right direction. This is especially important if you own a Ford, as we are aware of a number of known issues with Ford & Lincoln models.

    The second step is to locate all of the components associated with the Throttle Actuator Control System. This will include the throttle body, throttle position sensor, throttle actuator control motor, the PCM and the accelerator position sensor on a simplex system. Once these components are located a thorough visual inspection should be performed to check all of the associated wiring for obvious defects such as scraping, rubbing, bare wires, burn spots or melted plastic. Next is to check the connectors to every component for security, corrosion and damaged pins.

    The last visual and physical inspection is the throttle plate. With the ignition switch off, you should be able to rotate the throttle plate by pushing in on it. It should rotate to the wide open position. If there is sludge behind the plate it should be cleaned while it is accessible.

    Advanced Steps

    The advanced steps become very vehicle specific and require the appropriate advanced equipment to perform accurately. These procedures require a digital multi meter and the specific technical references for the vehicle. Voltage requirements will very based of the specific year, model and engine in the vehicle.

    Circuit Checks

    With the ignition switch in the off position, disconnect the electrical connector at the throttle body. Locate the 2 pins that go the motor or motors on the throttle body. Using a digital ohmmeter set to ohms, check the resistance of the motor or motors. The motor should read approximately between 2 and 25 ohms depending on the specific vehicle (check manufacturers specs for your vehicle). If the resistance is either too high or too low, the throttle body will need to be replaced. If all tests have passed so far, you will want to check the voltage signals to the motor.

    If this process identifies the absence of a power source or ground, continuity testing may be required to check the integrity of the wiring. Continuity tests should always by performed with the power removed from the circuit and the normal readings should be 0 ohms of resistance unless otherwise specified by the technical data. Resistance or no continuity is an indication of faulty wiring that must be repaired or replaced.

    Hopefully, the information in this article has been helpful to point you in the right direction to correct the problem with your Throttle Actuator Control System. This article is strictly informational and the specific technical data and service bulletins for your vehicle should always take priority.

    External Links

    Here are links to some discussions of Ford vehicles with the P2107 code:

  • Ford F150 P2107 and P2110
  • Ford Freestyle Throttle Body TSB
  • Ford Flex Throttle Actuator Failure?
  • Need help?

    Let us fix your problem. You are most welcome our diagnosis experts have in most cases the knowledge and skills to find the cause of the error code p2107 and to solve the problems.

    Make an appointment for diagnosis

    "Delete Error Code Permanently, Disable DTC Error Code Function for p2107 in the ECU"

    In extreme cases, we even have the option to permanently remove the specific DTC p2107 and disable the function of the specific error code in the ECU. All other fault code functions will then continue to work to protect the engine. This is different from clearing an error code with a diagnostic device. We have the option to permanently remove the function of the specific error code, so that it never comes back. Also emergency running that occurs on the specific error code can be solved in most cases.

    Of course we prefer to first try to solve the cause of the error code, but sometimes the only solution is to permanently disable the DTC function of p2107.

    Make an appointment for permanent removal of p2107