P0995 Transmission Fluid Pressure Sensor/Switch “F” Circuit High

Home » OBD Codes » P0900-P0999 » P0995 Transmission Fluid Pressure Sensor/Switch “F” Circuit High

P0995 Transmission Fluid Pressure Sensor/Switch “F” Circuit High

OBD-II Trouble Code Technical Description

Transmission Fluid Pressure Sensor / Switch "F" Circuit High

What does that mean?

This generic powertrain/engine diagnostic trouble code typically applies to all OBD-II equipped vehicles including but not limited to Dodge, Chrysler, Chevrolet, GMC, Acura, Toyota, etc. but seems to be most commonly seen on Honda vehicles.

The Transmission Fluid Pressure Sensor/Switch (TFPS) is usually found attached to the side of the valve body inside the transmission, although sometimes it may be found screwed into the side of the transmission case/body itself.

The TFPS converts the mechanical transmission pressures into an electrical signal for the Powertrain Control Module (PCM) or Transmission Control Module (TCM). Typically, the PCM/TCM will then inform other controllers utilizing the vehicle’s data communication bus.

The PCM/TCM receives this voltage signal to determine transmission operating pressure or when a shift is occurring. This code is set if this "F" input does not match normal operating voltages stored in the PCM/TCM’s memory. Refer to a vehicle specific repair manual to determine which is the "F" circuit for your particular vehicle.

P0995 is typically an electrical circuit (TFPS sensor circuit) issue. This cannot be overlooked in the troubleshooting stage, especially when dealing with an intermittent problem.

Troubleshooting steps may vary depending upon manufacturer, type of TFPS sensor and wire colors.

Related trans fluid pressure sensor "F" circuit codes:

  • P0992 Transmission Fluid Pressure Sensor/Switch "F" Circuit
  • P0993 Transmission Fluid Pressure Sensor/Switch "F" Circuit Range/Performance
  • P0994 Transmission Fluid Pressure Sensor/Switch "F" Circuit Low
  • P0996 Transmission Fluid Pressure Sensor/Switch "F" Circuit Intermittent
  • Code Severity & Symptoms

    Severity depends upon which circuit the failure has occurred in. Since this is an electrical failure, the PCM/TCM can compensate to some degree. The failure may mean that the PCM/TCM modifies the shifting of the transmission if electronically controlled.

    Symptoms of a P0995 engine code may include:

  • Malfunction Indicator Light On
  • Change in shift quality
  • Vehicle starts off in 2nd or 3rd gear (limp in mode)
  • Causes

    Typically the causes for this code to set are:

  • Short to power in the signal circuit to the TFPS sensor – possible
  • Open on ground circuit to the TFPS sensor – possible
  • Failed TFPS Sensor / internally shorted – likely
  • Failed PCM – unlikely (programming required after replacement)
  • Diagnostic and Repair Procedures

    A good starting point is always to check for technical service bulletins (TSB) for your particular vehicle. Your issue may be a known issue with a known fix put out by the manufacturer and can save you time and money during diagnosis.

    A good example of this would be if there are any known power related codes set along with the P0995, or if there is more than one pressure sensor/switch code set. If so, begin your diagnosis with the power related fault code first, or with the multiple code diagnosis first, as this may be the reason for the P0995.

    Next, locate the Transmission Fluid Pressure Sensor/Switch (TFPS) on your particular vehicle. The TFPS is usually found attached to the side of the valve body inside the transmission, although sometimes it may be found screwed into the side of the transmission case/body itself. Once located, visually inspect the connector and wiring. Look for scraping, rubbing, bare wires, burn spots or melted plastic. Pull the connector apart and carefully inspect the terminals (the metal parts) inside the connector. See if they look burned or have a green tint indicating corrosion, especially if they are attached outside the transmission case. Use electrical contact cleaner and a plastic bristle brush if cleaning of the terminals is needed. Let dry and apply electrical grease where the terminals contact.

    If you have a scan tool, clear the diagnostic trouble codes from memory, and see if P0995 code returns. If it does not, then the connections were most likely your problem.

    This is the most common area of concern for this code, as the external transmission connections have the greatest number of issues with corrosion.

    If the P0995 code does return, we will need to test the TFPS sensor and its associated circuits. With the Key Off, disconnect the electrical connector at the TFPS sensor. Connect a Digital Voltmeter (DVOM) black lead to the ground or low reference terminal at the TFPS sensor wiring harness connector. Connect the red lead of the Digital Voltmeter to the signal terminal at the TFPS sensor wiring harness connector. Turn Key On Engine Off. Check manufacturer’s specifications; voltmeter should read either 12 volts or 5 volts. Wiggle the connections to see if they change. If the voltage is incorrect, repair the power or ground wire, or replace the PCM/TCM.

    If the prior test passed, connect one lead of an ohmmeter to the signal terminal at the TFPS sensor and the other lead to the ground or low reference terminal at the sensor. Check manufacturers specifications on the resistance of the sensor to accurately test the resistance to pressure when there is no pressure applied to it. Wiggle the connector at the Transmission Fluid Pressure Sensor/Switch while monitoring the resistance. If the ohmmeter readings do not pass, replace the TFPS.

    If all prior tests have passed and you continue to get a P0995, this would most likely indicate a failed TFPS sensor, although a failed PCM/TCM could not be ruled out, nor could internal transmission malfunctions until the TFPS sensor had been replaced. If unsure, seek assistance from a trained automotive diagnostician. PCM/TCMs must be programmed, or calibrated to the vehicle in order to be installed correctly.

    Need help?

    Let us fix your problem. You are most welcome our diagnosis experts have in most cases the knowledge and skills to find the cause of the error code p0995 and to solve the problems.

    Make an appointment for diagnosis

    "Delete Error Code Permanently, Disable DTC Error Code Function for p0995 in the ECU"

    In extreme cases, we even have the option to permanently remove the specific DTC p0995 and disable the function of the specific error code in the ECU. All other fault code functions will then continue to work to protect the engine. This is different from clearing an error code with a diagnostic device. We have the option to permanently remove the function of the specific error code, so that it never comes back. Also emergency running that occurs on the specific error code can be solved in most cases.

    Of course we prefer to first try to solve the cause of the error code, but sometimes the only solution is to permanently disable the DTC function of p0995.

    Make an appointment for permanent removal of p0995