P0802 Transmission Control System MIL Request Circuit/Open
OBD-II Trouble Code Technical Description
Transmission Control System MIL Request Circuit/Open
What does that mean?
This diagnostic trouble code (DTC) is a generic powertrain code and applies to many OBD-II vehicles (1996-newer). That may include but is not limited to vehicles from Chevrolet, Kia, GMC, Dodge, Ford, Ram, etc. Although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration.
If your vehicle has stored a code P0802, it means that the powertrain control module (PCM) has received a data input signal indicating that the transmission control system (TCS) has detected a malfunction which requires malfunction indicator lamp (MIL) illumination.
The transmission control module (TCM) may be stand alone unit but is most commonly integrated into a single housing with the engine control module (ECM). This is what is referred to as the PCM.
The PCM utilizes input signals from multiple engine and transmission sensors to calculate automatic transmission shift strategy. A high pressure pump (inside the transmission) forces fluid through the valve body and into the sprag assembly; in addition to lubricating and cooling the transmission. The high pressure fluid allows the clutches to separate from the sprag momentarily so that the gear ratio may be changed smoothly. One or more electronic pressure control (EPC) solenoids help to regulate fluid pressure. Electronic pressure (EP) sensors provide the PCM with pertinent data regarding fluid pressure at various points in the transmission. Electronic shift solenoids are used to interrupt the flow of high pressure fluid so that the transmission shifts gears when commanded. The PCM uses voltage input signals from the transmission input speed sensor and transmission output speed sensor to determine if the transmission is shifting efficiently.
As with many other automatic transmission malfunctions, a transmission control system code may be caused by either an electrical or mechanical failure. If the PCM detects a malfunction which demands MIL illumination, a code P0802 will be stored and a MIL illuminated
A typical transmission control module:
What is the severity of this DTC?
A stored code P0802 indicates that a potentially serious TCS malfunction has been detected. Conditions which contributed to a code of this nature being stored should be rectified as quickly as possible.
What are some of the symptoms of the code?
Symptoms of a P0802 trouble code may include:
What are some of the common causes of the code?
Causes for this code may include:
What are some P0802 troubleshooting steps?
When diagnosing automatic transmission codes, you should begin by making sure that the transmission fluid is clean and that the transmission if filled to the appropriate level. If the fluid level is low, locate the source of the leak and repair the condition. Refill the transmission with the recommended fluid and proceed.
If the fluid is excessively dark and smells strongly of burnt friction material, it will need to be replaced. This can be accomplished by removing the transmission pan (and draining the torque converter) or flushing the transmission (recommended). Either way, you will want to replace the filter at this time too. When removing the pan from the transmission, take care to preserve whatever debris may have landed therein. If the pan is relatively clear of debris you can assume that the clutches are mechanically intact. If there is an excessive amount of friction material in the pan (and stuck to the magnet), the transmission will require a rebuild from a qualified technician.
A diagnostic scanner, a digital volt/ohmmeter (DVOM), and a source of vehicle specific diagnostic information will be required to diagnose a code P0802.
You may use your source of vehicle information to locate a technical service bulletin (TSB) that matches the vehicle year, make, and model; as well as the engine size, code/s stored, and symptoms exhibited. If you find one, it could yield helpful diagnostic information.
With the transmission filled to the appropriate level with the recommended fluid, proceed with the first step of the diagnosis.
Step 1
Use the scanner (connected to the vehicle diagnostic connector) to retrieve all stored codes and pertinent freeze frame data. It is a good idea to write this information down before clearing the codes then test-drive the vehicle until the PCM either enters readiness mode or the code is reset.
If the PCM enters readiness mode at this time, the code is intermittent and may be much more difficult to diagnose. If this is the case, the conditions which contributed to the code being stored may need to worsen before an accurate diagnosis can be made.
Step 2
If the code is immediately reset, the next step of your diagnosis will require that you search your vehicle information source for diagnostic flow-charts, connector pin-out charts, connector face views, and component testing procedures/specifications.
Step 3
Use the DVOM to test voltage and ground circuits at the TCM/PCM. If voltage and ground are detected, use the DVOM to check controller output. Begin by testing components and sensors related to specific symptoms. Any components which fail to comply with recommended specifications should be considered defective.
Step 4
If no transmission control components have failed, use the DVOM to test system circuits. The voltage drop testing method works well for this task. Disconnect all controllers from the circuit prior to testing resistance with the DVOM.
Need help?
Let us fix your problem. You are most welcome our diagnosis experts have in most cases the knowledge and skills to find the cause of the error code p0802 and to solve the problems.
Make an appointment for diagnosis
"Delete Error Code Permanently, Disable DTC Error Code Function for p0802 in the ECU"
In extreme cases, we even have the option to permanently remove the specific DTC p0802 and disable the function of the specific error code in the ECU. All other fault code functions will then continue to work to protect the engine. This is different from clearing an error code with a diagnostic device. We have the option to permanently remove the function of the specific error code, so that it never comes back. Also emergency running that occurs on the specific error code can be solved in most cases.
Of course we prefer to first try to solve the cause of the error code, but sometimes the only solution is to permanently disable the DTC function of p0802.
