P0629 Fuel Pump “A” Control Circuit High

Home » OBD Codes » P0600-P0699 » P0629 Fuel Pump “A” Control Circuit High

P0629 Fuel Pump “A” Control Circuit High

OBD-II Trouble Code Technical Description

Fuel Pump A Control Circuit High

What does that mean?

This is a generic powertrain diagnostic trouble code (DTC) and applies to many OBD-II vehicles (1996-newer). That may include but is not limited to vehicles from Ford, Dodge, Toyota, Chrysler, Jeep, Ram, Chevrolet, Nissan, Mitsubishi, Mercedes, etc. Although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration.

If the P0629 code appears, it means that a problem has been found in the fuel pump "A" control circuit. Specifically it means that a higher than normal voltage situation has been detected. Typically, it is brought on by damaged wires/connectors within the circuit or the Controller Area Network (CAN) bus. The Powertrain Control Module (PCM) or the Engine Control Module (ECM) normally identifies this code, however other supporting modules can also spark up this particular code such as:

  • Alternative Fuel Control Module
  • Fuel Injection Control Module
  • Turbo Control Module
  • Depending on the make and model of the vehicle it may be several drive cycles before it is able to activate this code or it can also be an immediate reaction as soon as the ECM recognizes the fault.

    The fuel pump is integral in the overall drivability of the vehicle. After all, without the fuel pump, there would be no fuel being delivered to the engine. The control circuit, generally speaking, is responsible for turning the pump on and off depending on the operator’s needs. An open within said circuit could also cause the P0629 code to become active so be aware of this before proceeding with any kind of diagnosing.

    A typical fuel pump:

    Related fuel pump A control circuit codes include:

  • P0627 Fuel Pump "A" Control Circuit /Open
  • P0628 Fuel Pump "A" Control Circuit Low
  • P0629 Fuel Pump "A" Control Circuit High
  • P062A Fuel Pump "A" Control Circuit Range/Performance
  • What is the severity of this DTC?

    This particular trouble code is a moderately severe problem for your vehicle. You can still utilize your vehicle despite the problem. However, it is highly advised to avoid doing so, because you may risk intermittently delivering fuel to the engine and an erratic or fluctuating fuel mixture could definitely result in severe engine damage.

    What are some of the symptoms of the code?

    Symptoms of a P0629 trouble code may include:

  • The check engine light is illuminated
  • Engine won’t start
  • Engine misfire/stall
  • Engine starts but dies
  • Fuel economy is reduced
  • Engine cranks fine but does not start
  • Engine dies when reaching operating temperature
  • Note: It is still possible that problem is actually unresolved, even if the check engine light does not light up immediately. Always ensure your vehicle has gone through a few drive cycles. i.e. drive the car for a week, if CEL (check engine light) is not illuminated by the end, the issue is most likely resolved.

    What are some of the common causes of the code?

    Causes for this code may include:

  • Issues with the fuel pump itself
  • Severed or damaged ground wire in the device’s control module
  • Unattached ground strap in the control module
  • Open, shorted, or corroded wiring in the CAN bus
  • A faulty CAN bus
  • Unsecured harnesses and wires causing a chafe or broken circuit
  • High resistance in circuit (e.g. melted/corroded connectors, internal wire corrosion)
  • What are some P0629 troubleshooting steps?

    The first thing I recommend you do is to research the Technical Service Bulletins (TSB’s) for the specific vehicle by year, model and power plant. In some circumstances, this can save a lot of time in the long run by pointing you in the right direction.

    Basic Step 1

    You always should immediately scan and test each module with the use of an OBD-II scanner, to get a good idea of the overall electrical condition of your vehicle and it’s modules. You should also always do a visual inspection of the connectors and wiring, in case there is anything obviously damaged, in which case it should be repaired or replaced. A lot of times, these are located under the vehicle near the fuel tank. They are susceptible to road debris and the elements so pay close attention to the health of these.

    Basic Step 2

    When dealing with any component with its own module (e.g. fuel pump module, etc.), you should examine the ground circuits. You can do this with the use of a separate battery ground. At times, you can do this easily by using an auxiliary ground cable. If your problem is rectified with the auxiliary ground attached but then, comes back when OEM ground is used, this would mean your ground cable is causing the issue and needs to be repaired or replaced. Grounds should always be thoroughly inspected for corroded connections. terminal, pins, etc. that could be causing the resistance of the circuit. A good sign of excessive corrosion is a green ring around the connector attached to the positive battery terminal. If this is present, remove the terminal and clean all contact point, the connector face and the terminal post/stud.

    Basic Step 3

    Given the fact that the cause of P0629 code could be an open circuit, you should identify the circuit using an electrical wiring diagram out of your service manual. Once identified, you can trace the individual fuel pump A control wire individually to see if there are any obvious breaks in the wire. Repair as necessary either by soldering the wire (which I recommend) or using butt connectors with heat shrink to insulate it from the elements. Using your multimeter you can measure the resistance between connectors in the circuit to pinpoint the location of the short/open. A power probe style tool here is highly recommended if there is a fault somewhere inside the entire circuit.

    I hope that this article has been helpful to point you in the right direction to diagnose the problem with your fuel pump control circuit trouble code. This article is strictly informational and the specific technical data and service bulletins for your vehicle should always take priority.

    Need help?

    Let us fix your problem. You are most welcome our diagnosis experts have in most cases the knowledge and skills to find the cause of the error code p0629 and to solve the problems.

    Make an appointment for diagnosis

    "Delete Error Code Permanently, Disable DTC Error Code Function for p0629 in the ECU"

    In extreme cases, we even have the option to permanently remove the specific DTC p0629 and disable the function of the specific error code in the ECU. All other fault code functions will then continue to work to protect the engine. This is different from clearing an error code with a diagnostic device. We have the option to permanently remove the function of the specific error code, so that it never comes back. Also emergency running that occurs on the specific error code can be solved in most cases.

    Of course we prefer to first try to solve the cause of the error code, but sometimes the only solution is to permanently disable the DTC function of p0629.

    Make an appointment for permanent removal of p0629