P0522 Engine Oil Pressure Sensor/Switch Circuit Low Voltage
OBD-II Trouble Code Technical Description
Generic: Engine Oil Pressure Sensor/Switch Low
Chrysler: Oil Pressure Sensor Low Input Conditions
GM: Engine Oil Pressure Sensor Circuit Low Input Conditions
This diagnostic trouble code (DTC) is a generic OBD-II powertrain code. It is considered generic because it applies to all makes and models of vehicles (1996-newer), although specific repair steps may vary depending on the model. In our experience the P0522 engine code appears more often on Chevrolet, Dodge, GMC, Cadillac, and Buick, but applies to any make/model.
What does that mean?
The vehicle’s main computer called the Powertrain Control Module (PCM) is in control of many sensors, controls, and electronics in the vehicle. One of the sensors called the oil pressure sensor or sender detects the amount of (mechanical) oil pressure in the engine and relays that in the form of a voltage reading/value to the PCM. In some vehicles, that oil pressure value is then relayed to a gauge in the instrument cluster to show the driver the oil pressure, other times that gauge is not there but there will be a warning light if there is a problem.
This specific P0522 engine code is triggered when the PCM sees too low of a value in the engine oil pressure sender/sensor. If the engine oil pressure actually does drop too low, the engine can be permanently damaged, so if you notice low oil pressure, it is critical that you pull over and shut off the vehicle as soon as safely possible. For this trouble code, the cause is more than likely electrical related.
Note: This code is severe, you need to act right away to diagnose & repair. This code is related to P0520, P0521, P0523, and P0524.
Symptoms
Symptoms of a P0522 DTC may include:
Causes
Potential causes of a P0522 code include:
Diagnostic & Repair Steps
NOTE: There is a known service bulletin that applies to a number of GM vehicles including Chevrolet, Cadillac, GMC, Pontiac, Buick, and Saab. The bulletin number is PIP4786.
Check for any applicable TSBs (Technical Service Bulletins) for your vehicle even if it’s not one of those before going too far into diagnostics. There is also a TSB for certain 2011 model year Chrysler & Dodge vehicles where the fix is to reprogram the PCM.
First and especially if you have other oil related DTCs, check the oil level & condition. Make sure you have the correct type and weight of oil and the oil filter is not clogged.
Visually inspect the wiring and connectors at the oil pressure sending unit. Look for broken or frayed wires, burnt spots, loose or exposed wiring, etc. Refer to a model specific resource for the location of the sender. Do the same for the wiring and connectors leading to the PCM.
Use a digital volt ohm meter (DVOM) to check the sensor itself, and if it does not meet manufacturers specifications you should replace it. This is a 5 volt circuit. Replacing the sensor/sender will be the most likely repair for this code. If it checks out OK, test the wiring and connectors from the sensor to the PCM. Verify there are no breaks in the wiring or a short to ground due to chafing, pinching, etc. Make sure the electrical connectors are tight and corrosion free.
A technician may also put on a mechanical oil pressure gauge to verify actual oil pressure and compare that to the sensor reading using an advanced scan tool. If your problem is not resolved by fixing/replacing wiring/sensor then check the actual pressure in the engine.
As you can see there are a number of possible reasons for this code P0522. If the sending unit is cheap you could try replacing it first and see if that fixes it, but a proper diagnosis definitely recommended so you don’t replace perfectly good parts. Good luck, if you need help stop by our car repair forum.
Need help?
Let us fix your problem. You are most welcome our diagnosis experts have in most cases the knowledge and skills to find the cause of the error code p0522 and to solve the problems.
Make an appointment for diagnosis
"Delete Error Code Permanently, Disable DTC Error Code Function for p0522 in the ECU"
In extreme cases, we even have the option to permanently remove the specific DTC p0522 and disable the function of the specific error code in the ECU. All other fault code functions will then continue to work to protect the engine. This is different from clearing an error code with a diagnostic device. We have the option to permanently remove the function of the specific error code, so that it never comes back. Also emergency running that occurs on the specific error code can be solved in most cases.
Of course we prefer to first try to solve the cause of the error code, but sometimes the only solution is to permanently disable the DTC function of p0522.
