P0443 Evaporative Emission Control System Purge Control Valve Circuit

Home » OBD Codes » P0400-P0499 » P0443 Evaporative Emission Control System Purge Control Valve Circuit

P0443 Evaporative Emission Control System Purge Control Valve Circuit

OBD-II Trouble Code Technical Description

Evaporative Emission Control System Purge Control Valve Circuit

What does that mean?

This diagnostic trouble code (DTC) is a generic powertrain code, which means that it applies to OBD-II equipped vehicles. Although generic, the specific repair steps may vary depending on make/model.

The Evaporative Emissions System (EVAP) allows fumes from the gas tank to enter the engine to be burned, rather than vented into the atmosphere as an emission. The purge valve solenoid is supplied switched battery voltage.

The ECM controls the valve by operating the ground circuit, opening the purge valve at specific times allowing these gasses to enter the engine. The ECM monitors the ground circuit as well, watching for faults. When the purge solenoid isn’t activated, the ECM should see a high voltage on the ground circuit. When the solenoid is activated, the ECM should see the ground voltage pulled low, close to zero. If the ECM doesn’t see these expected voltages, or senses an open in the circuit, this code is set.

Note: This DTC is similar to P0444 and P0445.

Potential Symptoms

P0443 trouble code symptoms could be just an malfunction indicator lamp (MIL) illumination. There may be no drivability problems at all. But, it’s also possible to have a lean condition or a rough running engine if the purge valve is stuck open. Usually though, these symptoms are accompanied by other EVAP codes. Another symptom may be excessive pressure in the gas tank in the form of a "whooshing" sound when the cap is removed, indicating a purge valve that isn’t working at all or stuck closed.

Causes

To cause a P0443, there has to be a problem with the purge control CIRCUIT , not necessarily the valve. Usually they are a unit housing the valve and the solenoid as an assembly. Or it could be comprised of a separate solenoid with vacuum lines to a purge valve. That said, it could be any of the following:

  • Bad purge solenoid (internal short or open)
  • Wiring harness chafing or rubbing another component causing short or open on control circuit
  • Connector worn, broken or shorted due to water intrusion
  • Driver circuit inside powertrain control module (PCM) is bad
  • Possible Solutions

    1. Using a scan tool, command the purge solenoid to activate. Listen or feel for a clicking coming from the purge solenoid. It should click once, or on some models it may click repeatedly.

    2. If it doesn’t click with scan tool activation, unplug the connector and examing the solenoid and connector for damage, water, etc. Then check for battery voltage on the feed wire with the key on. If you have battery voltage, then ground the control side manually using a jumper wire and see if the valve clicks. If it does, then you know the solenoid is working properly but there is a problem with the control circuit. If it doesn’t click when you manually ground it, replace the purge solenoid.

    3. To check for a problem on the control circuit (if the solenoid tests okay and you have voltage to the solenoid) plug the solenoid back in and remove the control circuit (ground) wire from the ECM connector (If you’re unsure how to do this, do not attempt). With the ground wire removed from the ECM, turn the key on and then manually ground the Purge valve control wire. The solenoid should click. If it does, then you know there is no problem with the control wire to the solenoid and there is a problem with the ECM purge solenoid driver circuit in the ECM. You’ll need a new ECM. However if it doesn’t click, then there must be an open in the wiring between the ECM and and the solenoid. You must find it and repair it.

    Other EVAP DTCs: P0440 – P0441 – P0442 – P0444 – P0445 – P0446 – P0447 – P0448 – P0449 – P0452 – P0453 – P0455 – P0456

    Need help?

    Let us fix your problem. You are most welcome our diagnosis experts have in most cases the knowledge and skills to find the cause of the error code p0443 and to solve the problems.

    Make an appointment for diagnosis

    "Delete Error Code Permanently, Disable DTC Error Code Function for p0443 in the ECU"

    In extreme cases, we even have the option to permanently remove the specific DTC p0443 and disable the function of the specific error code in the ECU. All other fault code functions will then continue to work to protect the engine. This is different from clearing an error code with a diagnostic device. We have the option to permanently remove the function of the specific error code, so that it never comes back. Also emergency running that occurs on the specific error code can be solved in most cases.

    Of course we prefer to first try to solve the cause of the error code, but sometimes the only solution is to permanently disable the DTC function of p0443.

    Make an appointment for permanent removal of p0443