P032C Knock Sensor 3 Circuit Low Bank 1

Home » OBD Codes » P0300-P0399 » P032C Knock Sensor 3 Circuit Low Bank 1

P032C Knock Sensor 3 Circuit Low Bank 1

OBD-II Trouble Code Technical Description

Knock Sensor 3 Circuit Low (Bank 1)

What does that mean?

This diagnostic trouble code (DTC) is a generic powertrain code, which means that it applies to OBD-II equipped vehicles (Dodge, Ram, Ford, GMC, Chevrolet, VW, Toyota, etc.). Although generic, the specific repair steps may vary depending on make/model.

A P032C trouble code means that the powertrain control module (PCM) has detected a lower than expected sensor reading from the knock sensor #3 on bank 1. Bank 1 is always the bank of engine cylinders that contains the #1 cylinder. Refer to a vehicle specific repair source to determine which sensor is knock sensor #3.

Typically threaded directly into the engine block, the knock sensor is a piezoelectric sensor. The location of the sensors in a multi-sensor system may vary between manufacturers but most are in the sides of the block (between water jacket freeze plugs). Knock sensors that are in the sides of the engine block are often threaded directly into engine coolant passages. When the engine is warm and the engine cooling system is under pressure, removal of these sensors could result in severe burns from hot coolant. Before removing a knock sensor, allow the engine to cool and always dispose of coolant properly.

A piezoelectric sensing crystal is at the heart of the knock sensor. When shaken or vibrated, the piezoelectric crystal produces a small amount of voltage. Since the knock sensor control circuit is normally a one-wire ground circuit, the voltage generated by the vibration is recognized by the PCM as engine noise or vibration. The severity of the vibration encountered by the piezoelectric crystal (inside the knock sensor) determines the level of voltage produced in the circuit.

If the PCM detects a degree of knock sensor voltage indicative of a spark detonation; it may retard ignition timing and no knock sensor control code may be stored. If the PCM detects a level of knock sensor voltage that indicates a more severe engine noise (such as a connecting rod contacting the inside of the engine block), it may discontinue fuel delivery and ignition spark to the affected cylinder and a knock sensor code will be stored.

Code Severity & Symptoms

A stored code P032C should be considered severe because it could indicate internal engine failure.

Symptoms of this code may include:

  • Hesitation when accelerating
  • Below normal engine performance
  • Abnormal noises from the engine area
  • Increased fuel consumption
  • Causes

    Potential causes for this code to set are:

  • Ignition misfire
  • Faulty knock sensor
  • Internal engine problem
  • Contaminated or subpar fuel used
  • Defective knock sensor control wiring and/or connectors
  • Bad PCM or a PCM programing error
  • Diagnostic and Repair Procedures

    To diagnose a code P032C, a diagnostic scanner, a digital volt/ohmmeter (DVOM), and a reliable vehicle specific repair resource will be necessary. If the engine sounds like it is knocking, or excessively noisy, address that issue before attempting a diagnosis for any knock sensor codes.

    Check for technical service bulletins (TSBs) that may apply to your year/make/model. If the issue is a known issue there may exist a bulletin to help with diagnosis and repair specific to your exact problem. That can save you time and money.

    Start with a visual inspection of all system related wiring harnesses and connectors. Look for corroded, burnt, or otherwise damaged wiring and connectors that may create an open or shorted circuit. Knock sensors are often in the lower part of the engine block. This makes them susceptible to damage when heavy parts (like starters and engine mounts) are replaced. System connectors, wiring, and fragile knock sensors are frequently broken during repairs in the vicinity.

    Connect the OBD-II scanner to the vehicle diagnostic connector and retrieve all stored diagnostic codes and freeze frame data. Write this information down for use in the diagnostic process. Clear the codes and test drive the vehicle to see if any are reset.

    If the P032C is reset, start the engine and use the scanner to observe knock sensor data. If the scanner indicates that knock sensor voltage is not within manufacturer’s specifications, use the DVOM to test live data at the knock sensor connector. If the signal at the connector is within specs, suspect a wiring issue between the sensor and the PCM. If voltage at the knock sensor connector is not within specifications, suspect a defective knock sensor. If replacement of the sensor is the next step, be sure to ensure you don’t come in contact with hot coolant. Wait for the engine to cool before removing the old sensor.

    Need help?

    Let us fix your problem. You are most welcome our diagnosis experts have in most cases the knowledge and skills to find the cause of the error code p032c and to solve the problems.

    Make an appointment for diagnosis

    "Delete Error Code Permanently, Disable DTC Error Code Function for p032c in the ECU"

    In extreme cases, we even have the option to permanently remove the specific DTC p032c and disable the function of the specific error code in the ECU. All other fault code functions will then continue to work to protect the engine. This is different from clearing an error code with a diagnostic device. We have the option to permanently remove the function of the specific error code, so that it never comes back. Also emergency running that occurs on the specific error code can be solved in most cases.

    Of course we prefer to first try to solve the cause of the error code, but sometimes the only solution is to permanently disable the DTC function of p032c.

    Make an appointment for permanent removal of p032c