P0328 Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)

Home » OBD Codes » P0300-P0399 » P0328 Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)

P0328 Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)

OBD-II Trouble Code Technical Description

Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)

What does that mean?

This diagnostic trouble code (DTC) is a generic powertrain code, which means that it applies to OBD-II equipped vehicles. Although generic, the specific repair steps may vary depending on make/model.

Knock sensors are used to detect engine pre-detonation (engine knock or ping). The knock sensor (KS) is usually a two wire sensor. A 5 volt reference is supplied to the sensor and there is a signal return from the knock sensor to the PCM (powertrain control module).

The sensor signal wire informs the PCM when a knock occurs and in what degree of severity. The PCM will retard the spark timing to avoid pre-detonation. Most PCMs have the ability to learn spark knock trends in the engine during normal operation.

A P0328 code is a generic DTC, thus it applies to all makes of vehicles, and refers to a high output voltage of the knock sensor. In many cases, this means the voltage is above 4.5V but that specific value depends on the specific make and model of vehicle. This code refers to the sensor on bank #1.

Symptoms

Symptoms of a P0328 DTC may include:

  • MIL (Malfunction Indicator Lamp) illumination
  • Audible knocking from the engine compartment
  • Pinging from engine under acceleration
  • Loss of power
  • Irregular RPM
  • Causes

    Potential causes of a P0328 code include:

  • Knock sensor connector is damaged
  • Knock sensor circuit is open or shorted to ground
  • Knock sensor circuit is shorted to voltage
  • Knock sensor has failed
  • Loose knock sensor
  • Electrical interference in circuit
  • Low fuel pressure
  • Incorrect fuel octane
  • Mechanical engine problem
  • Failed/faulty PCM
  • Possible Solutions

    If you can hear engine knock (detonation), first fix the source of the mechanical problem and retest. Ensure the correct octane fuel was used (some engines require premium fuel, check the owners manual). Aside from that, for this code, most likely the problem will lie either with the knock sensor itself or the wiring & connectors going from the sensor to the PCM.

    Realisitcally, for the DIY vehicle owner, the best next steps are to measure the resistance between the two knock sensor wire terminals where they go into the PCM. Also, check the voltage of the same terminals. Compare those numbers to the manufacturer’s specifications. Also, check all wiring and connectors leading from the knock sensor back to the PCM. In addition, you should also check the resistance using a Digital Volt Ohm Meter (DVOM) of the knock sensor itself, compare it to the vehicle manufacturers specification. If the knock sensor resistance value is out of spec, then it needs to be replaced.

    Other knock sensor DTCs include P0324, P0325, P0326, P0327, P0328, P0329, P0330, P0331, P0332, P0334

    Need help?

    Let us fix your problem. You are most welcome our diagnosis experts have in most cases the knowledge and skills to find the cause of the error code p0328 and to solve the problems.

    Make an appointment for diagnosis

    "Delete Error Code Permanently, Disable DTC Error Code Function for p0328 in the ECU"

    In extreme cases, we even have the option to permanently remove the specific DTC p0328 and disable the function of the specific error code in the ECU. All other fault code functions will then continue to work to protect the engine. This is different from clearing an error code with a diagnostic device. We have the option to permanently remove the function of the specific error code, so that it never comes back. Also emergency running that occurs on the specific error code can be solved in most cases.

    Of course we prefer to first try to solve the cause of the error code, but sometimes the only solution is to permanently disable the DTC function of p0328.

    Make an appointment for permanent removal of p0328