P0225 Throttle/Pedal Position Sensor/Switch C Circuit Malfunction

Home » OBD Codes » P0200-P0299 » P0225 Throttle/Pedal Position Sensor/Switch C Circuit Malfunction

P0225 Throttle/Pedal Position Sensor/Switch C Circuit Malfunction

OBD-II Trouble Code Technical Description

Throttle Position Sensor/Switch (TPS) C Circuit Malfunction

What does that mean?

This diagnostic trouble code (DTC) is a generic powertrain code, which means that it applies to OBD-II equipped vehicles. Although generic, the specific repair steps may vary depending on make/model.

The TPS (Throttle Position Sensor) is a potentiometer that is mounted to the throttle body. It detects the throttle blade angle. As the throttle blade moves, the TPS sends a signal to the PCM (Powertrain Control Module). Usually a three wire sensor: A 5 volt reference from the PCM to the TPS, a ground from the PCM to the TPS, and a signal return from the TPS to the PCM.

The TPS sends the throttle position information back to the PCM on this signal wire. When the throttle is closed the signal is near .45 volts. At WOT (Wide Open Throttle) the TPS signal voltage will approach a full 5 volts. When the PCM sees a voltage that is outside of normal operating range, P0225 will set. The C refers to a particular circuit, sensor, or area of a particular circuit.

NOTE: The PCM knows that any large change in throttle position means a cooresponding change in manifold pressure (MAP). On some models the PCM will monitor MAP and TPS operation for comparison. Meaning that if the PCM sees a large percentage change in throttle position, it expects to see a cooresponding change in manifold pressure and vice versa. If it doesn’t see this comparitive change, P0225 may set. This doesn’t apply to all models.

Symptoms

Potential symptoms include:

  • MIL (Malfunction Indicator Lamp) illumination
  • Misfiring at idle or at highway speed
  • Poor idle quality
  • Possibly won’t idle
  • Possibly starts and stalls
  • Causes

    Potential causes of the P0225 code include:

  • Sticking throttle return spring
  • MAP or TPS connector corrosion
  • Misrouted harness causing chafing
  • Bad TPS
  • Bad PCM
  • Possible Solutions

    If you have access to a scan tool, with KOEO (Key on engine off) observe the TPS voltage. With throttle closed, voltage should be about .45 volts. It should gradually sweep upwards to approximately 4.5 to 5 volts as you depress the throttle. Sometimes only a scope can capture an intermittent glitch in the TPS signal voltage. If you notice a glitch in the TPS sweep voltage, replace the TPS.

    NOTE: Some TPS sensors require fine adjustment. If you aren’t comfortable with using a DVOM (Digital Volt Ohm meter) to adjust the new TPS, then it’s best to take the vehicle to a shop. If the voltage is not .45 volts (+or- .3 volts or so) with the throttle closed or if the reading is "stuck" then unplug the TPS connector. With KOEO check for 5 volts reference voltage present at the connector and a good ground. You can check the signal circuit for continuity by jumping a fused wire between the ground circuit of the TPS connector and the signal circuit. If the TPS reading on the scan tool now reads zero, then replace the TPS. However if that doesn’t change the reading to zero, then check for an open or a short on the signal wire and if none is found, suspect a bad PCM. If manipulating the TPS wiring harness causes any change in idle, then suspect bad TPS.

    Need help?

    Let us fix your problem. You are most welcome our diagnosis experts have in most cases the knowledge and skills to find the cause of the error code p0225 and to solve the problems.

    Make an appointment for diagnosis

    "Delete Error Code Permanently, Disable DTC Error Code Function for p0225 in the ECU"

    In extreme cases, we even have the option to permanently remove the specific DTC p0225 and disable the function of the specific error code in the ECU. All other fault code functions will then continue to work to protect the engine. This is different from clearing an error code with a diagnostic device. We have the option to permanently remove the function of the specific error code, so that it never comes back. Also emergency running that occurs on the specific error code can be solved in most cases.

    Of course we prefer to first try to solve the cause of the error code, but sometimes the only solution is to permanently disable the DTC function of p0225.

    Make an appointment for permanent removal of p0225