P0100 Mass or Volume Air Flow “A” Circuit Malfunction

Home » OBD Codes » P0100-P0199 » P0100 Mass or Volume Air Flow “A” Circuit Malfunction

P0100 Mass or Volume Air Flow “A” Circuit Malfunction

Technical Description

Mass or Volume Air Flow (MAF) Circuit Malfunction

What does that mean?

This diagnostic trouble code (DTC) is a generic powertrain code, which means that it applies to OBD-II equipped vehicles that have a mass airflow sensor. Brands include but are not limited to Toyota, Nissan, Vauxhall, Mercedes Benz, Mitsubishi, VW, Saturn, Ford, Jeep, Jaguar, Chevy, Infiniti, etc. Although generic, the specific repair steps may vary depending on make/model.

The MAF (mass air flow) sensor is a sensor mounted in a vehicle’s engine air intake tract downstream from the air filter, and is used to measure the volume and density of air being drawn into the engine. The MAF sensor itself only measures a portion of the air entering and that value is used to calculate the total volume and density of air being ingested.

The powertrain control module (PCM) uses that reading along with other sensor parameters to ensure proper fuel delivery at any given time for optimum power and fuel efficiency.

This P0100 diagnostic trouble code (DTC) means that there is a detected problem with the Mass Air Flow (MAF) sensor or circuit. The PCM detects that the actual MAF sensor frequency signal is not performing within the normal expected range of the calculated MAF value.

Note: Some MAF sensors also incorporate an air temperature sensor, which is another value used by the PCM for optimal engine operation.

Closely related MAF circuit trouble codes include:

  • P0101 Mass or Volume Air Flow "A" Circuit Range/Performance
  • P0102 Mass or Volume Air Flow "A" Circuit Low Input
  • P0103 Mass or Volume Air Flow "A" Circuit High Input
  • P0104 Mass or Volume Air Flow "A" Circuit Intermittent
  • Photo of a MAF sensor:

    What are some possible symptoms?

    Symptoms of a P0100 code may include:

  • Malfunction indicator lamp (MIL) illumination (a.k.a. check engine light)
  • Rough running engine
  • Black smoke from tail pipe
  • Stalling
  • Engine hard start or stalling after it starts
  • Possible other driveability symptoms or even no symptoms
  • What are some potential causes?

    Potential causes for this trouble code may include:

  • Dirty or contaminated mass air flow sensor
  • Failed MAF sensor
  • Intake air leaks
  • MAF sensor electrical harness or wiring problem (open, shorted, frayed, poor connection, etc.)
  • Note that other codes may be present if you have a P0101. You may have misfire codes or O2 sensor codes, so it’s important to take a "big picture" look at how the systems work together and effect each other when doing a diagnosis.

    What can I do to diagnose and repair a P0100 engine code?

  • Visually inspect all MAF sensor wiring and connectors to make sure they are intact, not frayed, broken, routed too close to ignition wires/coils, relays, motors, etc.
  • Visually inspect for any obvious air leaks in the air intake system
  • Visually *closely* inspect the MAF sensor wires or film to see if you can see contamination such as dirt, dust, oil, etc.
  • If the air filter is dirty, replace it with a new original equipment filter from the dealer
  • Carefully clean the MAF using MAF cleaner spray is generally a good DIY friendly diagnostic/repair step
  • If the air intake system has a mesh in it, make sure that is also clean (VWs mainly)
  • Loss of vacuum to the MAP sensor can trigger this DTC
  • A low minimum air rate through the sensor bore may cause this DTC to set at idle or during deceleration. Inspect for any vacuum leaks downstream of the MAF sensor.
  • Use a scan tool to monitor real-time sensor values from the MAF sensor, O2 sensors, etc.
  • Check for Technical Service Bulletins (TSBs) for your particular make/model in case of known issues on your vehicle
  • The barometric pressure (BARO) that is used in order to calculate the predicted MAF value is initially based on the MAP sensor at key ON.
  • A high resistance on the ground circuit of the MAP sensor can cause this DTC to set
  • If you do need to replace the MAF sensor, we recommend using an original equipment OEM one from the manufacturer rather than buying an aftermarket part.

    Note: The use of a reusable oiled air filter could be a cause of this code, if it is over-oiled. Oil can transfer to the fine wire or film inside the MAF sensor and contaminate it. Use something such as MAF cleaner spray to clean the MAF in such situations. We do not recommend the use of oiled air filters.

    Need help?

    Let us fix your problem. You are most welcome our diagnosis experts have in most cases the knowledge and skills to find the cause of the error code p0100 and to solve the problems.

    Make an appointment for diagnosis

    "Delete Error Code Permanently, Disable DTC Error Code Function for p0100 in the ECU"

    In extreme cases, we even have the option to permanently remove the specific DTC p0100 and disable the function of the specific error code in the ECU. All other fault code functions will then continue to work to protect the engine. This is different from clearing an error code with a diagnostic device. We have the option to permanently remove the function of the specific error code, so that it never comes back. Also emergency running that occurs on the specific error code can be solved in most cases.

    Of course we prefer to first try to solve the cause of the error code, but sometimes the only solution is to permanently disable the DTC function of p0100.

    Make an appointment for permanent removal of p0100