P0092 Fuel Pressure Regulator 1 Control Circuit High
OBD-II Trouble Code Technical Description
Fuel Pressure Regulator 1 Control Circuit High
What does that mean?
This diagnostic trouble code (DTC) is a generic powertrain code, which means that it applies to OBD-II equipped vehicles (Isuzu, Mazda, Dodge, Chrysler, Ford, GMC, Chevy, Toyota, Honda, etc.). Although generic, the specific repair steps may vary depending on make/model.
In my experience with diagnosing a code P0092, it has meant that the powertrain control module (PCM) has detected a high voltage signal from the control circuit of the electronic fuel pressure regulator designated with a 1. Systems which have multiple electronic fuel pressure regulators use a numerical designation. It may refer to a certain engine bank but not always.
The PCM typically controls the electronic fuel pressure regulator. Battery voltage and ground signals are used to control a servo motor (in the fuel pressure regulator) which positions a valve so that the desired level of fuel pressure may be achieved for any given situation. In order to adjust fuel pressure regulator voltage, when necessary, the PCM monitors the fuel pressure sensor which is located in the fuel injector rail. When voltage is increased at the electronic fuel pressure regulator servo motor, a valve is opened and fuel pressure is increased. Decreased voltage at the servo causes the valve to close and fuel pressure decreases.
The fuel pressure regulator and fuel pressure sensor are most frequently integrated into a single housing (with one electrical connector) but may be separate components.
If actual fuel pressure regulator control circuit voltage is less than an expected degree, as computed by the PCM, a P0092 will be stored and a malfunction indicator lamp (MIL) may be illuminated.
Related fuel pressure regulator engine codes:
Symptoms & Severity
Since excessive fuel pressure may cause internal engine and catalytic converter damage and lead to various drivability issues, a code P0092 should be categorized as severe.
Symptoms of a P0092 code may include:
Causes
Potential causes for this code to set are:
Diagnostic and Repair Procedures
Diagnosing a code P0092 will require access to a diagnostic scanner, a digital volt/ohmmeter (DVOM), a suitable fuel pressure gauge, and a reliable vehicle information source (such as All Data DIY).
NOTE: Extreme caution must be exercised when using a manual fuel pressure gauge. High pressure fuel contacting hot surfaces or open spark could ignite and cause a fire.
A visual inspection of system wiring and connectors, with a focus on harnesses and connectors on top of the engine, has been fruitful for me in the past. It seems that the warm upper engine area is popular with varmints, especially in cold climates. Unfortunately, pests often gnaw system wiring and connectors repeatedly.
Next, I would connect the scanner to the vehicle diagnostic port and retrieve stored codes and freeze frame data. Writing this information down may prove helpful if the diagnostic process drags on. Clear the codes and test-drive the vehicle if the engine will start.
Check for the correct degree of voltage and a battery ground at the fuel pressure regulator, if the code is reset. If no voltage is found at the fuel pressure regulator connector, test power supply relays and fuses by following the appropriate wiring diagram from the vehicle information source. If no ground is present, the wiring diagram can help you to find the location of the fuel pressure regulator control system ground/s and make sure they are secure.
Suitable voltage and ground circuits, discovered at the fuel pressure control regulator connector, would prompt me to obtain fuel pressure specifications from the vehicle information source and test fuel system pressure using the fuel pressure gauge. Remember to follow manufacturer’s recommendations for using the fuel pressure gauge.
Monitor manual fuel pressure with the fuel gauge while using the scanner to observe fuel system data. A defective fuel pressure sensor may be at the root of your problems if the level of fuel pressure reflected on the scanner does not coincide with actual fuel pressure. Variations in fuel pressure regulator control voltage should reflect fluctuations in actual fuel rail pressure. If not, suspect that either the fuel pressure regulator is defective, there is an open or shorted circuit in one of the fuel pressure regulator control circuits, or that the PCM is bad.
In order to test the electronic fuel pressure regulator and the individual fuel pressure regulator control circuits, use the DVOM and follow manufacturer’s recommendations. Disconnect controllers from the circuit before testing circuit resistance and continuity with the DVOM.
Additional diagnostic notes:
Other fuel pressure trouble codes include:
Need help?
Let us fix your problem. You are most welcome our diagnosis experts have in most cases the knowledge and skills to find the cause of the error code p0092 and to solve the problems.
Make an appointment for diagnosis
"Delete Error Code Permanently, Disable DTC Error Code Function for p0092 in the ECU"
In extreme cases, we even have the option to permanently remove the specific DTC p0092 and disable the function of the specific error code in the ECU. All other fault code functions will then continue to work to protect the engine. This is different from clearing an error code with a diagnostic device. We have the option to permanently remove the function of the specific error code, so that it never comes back. Also emergency running that occurs on the specific error code can be solved in most cases.
Of course we prefer to first try to solve the cause of the error code, but sometimes the only solution is to permanently disable the DTC function of p0092.
