P0080 Exhaust Valve Control Solenoid Circuit High (Bank 1)
OBD-II Trouble Code Technical Description
Exhaust Valve Control Solenoid Circuit High (Bank 1)
What does that mean?
This code is a generic OBD-II powertrain code, that means it applies to all makes and models of vehicles (1996-newer), although specific repair steps may vary depending on the model.
On vehicles equipped with variable valve timing (VVT), the Engine Control Module / Powertrain Control Module (ECM/PCM) controls the camshaft position by regulating the engine oil through the control solenoid to change the position of the camshaft. The control solenoid is commanded using a Pulse Width Modulated signal (PWM) from the ECM/PCM. The ECM/PCM monitors this signal and if the voltage is above specification, it will set this trouble code and illuminate the Malfunction Indicator Lamp (MIL).
Bank 1 refers to the side of the engine with cylinder #1 – be sure to verify according to manufacturers specifications. The exhaust valve control solenoid is usually located on the Exhaust manifold side of the cylinder head. This code is similar to codes P0078 and P0079. This code may also be accompanied by P0027.
Symptoms
Symptoms of a P0080 may include:
Potential Causes
Potential causes may include:
Diagnostic Steps
Wire harness – Check for unplugged harness connections, look for corrosion or loose wires to connectors. Unplug harness connectors from Solenoid and PCM, using a wiring diagram locate the + and – wires to the solenoid. The solenoid can be ground side or power side controlled, depending on the application. Check with factory wiring diagrams to determine the power flow in the circuit. Using a digital volt ohm meter (DVOM) set to the ohms setting, check for resistance between each end of the wire. An over limit reading on the DVOM may be an open in the wiring, loose connection or terminal.
Control solenoid – With the electrical harness to the solenoid unplugged, using the DVOM set to ohms, check for resistance between each of the electrical terminals on the control solenoid itself. Use the factory specifications or a known good control solenoid if available to determine if there is resistance in the solenoid. If there is an over limit or very low resistance reading on the DVOM, the solenoid is likely faulty.
Short to power – Unplug the harness to the PCM/ECM and locate the wires to the control solenoid. With the DVOM set to the volts scale, connect the negative lead to ground and the positive lead to the wire(s) to the control solenoid. Check for voltage, if there voltage present there may be a short to power in the wiring harness. Locate the short to power by unplugging harness connectors and testing the wiring back to the solenoid.
PCM / ECM – If all wiring and the control solenoid checks out okay, it will be necessary to monitor the solenoid during engine operation by back probing the wires at the PCM/ECM. Using an advanced scan tool that will read the engine functions, monitor the duty cycle commanded to the control solenoid. It will be necessary to monitor the solenoid during engine operation under various engine RPM’s and load. Using an oscilloscope or graphing multimeter set to the duty cycle scale, connect the negative lead to a known good ground and the positive lead to either wire terminal at the solenoid itself. The reading on the multimeter tool should match the commanded duty cycle on the scan tool. If they are opposite, the polarity may be reversed – connect the positive lead on the other wire terminal to the solenoid and re-test to verify. If the signal detected from the PCM is constantly on, there may be a fault with the PCM itself.
Need help?
Let us fix your problem. You are most welcome our diagnosis experts have in most cases the knowledge and skills to find the cause of the error code p0080 and to solve the problems.
Make an appointment for diagnosis
"Delete Error Code Permanently, Disable DTC Error Code Function for p0080 in the ECU"
In extreme cases, we even have the option to permanently remove the specific DTC p0080 and disable the function of the specific error code in the ECU. All other fault code functions will then continue to work to protect the engine. This is different from clearing an error code with a diagnostic device. We have the option to permanently remove the function of the specific error code, so that it never comes back. Also emergency running that occurs on the specific error code can be solved in most cases.
Of course we prefer to first try to solve the cause of the error code, but sometimes the only solution is to permanently disable the DTC function of p0080.
